DRY FLOOR HEATING
span>
The installation of underfloor heating is primarily supported by thermal comfort, health, aesthetics and economy.
The use of an underfloor heating system brings many benefits, above all it allows you to get optimal vertical distribution of temperature in the room for humans. The heat is felt in the most comfortable way. A person feels best when he has warm legs and cool breathing air.
The premise of underfloor heating is that the floor is only a few degrees warmer than air. Thanks to this, there is no dust raising phenomenon and the heat stays in the users zone. This makes the so-called floor systems extremely friendly for people suffering from allergies.
It’s no wonder that this form of space heating is becoming increasingly popular. Relatively cheap to install, economical in operation and low maintenance, it makes practical sense. It also frees the wall space normally dedicated to radiators and can be installed in virtually any type of floor. It is widely considered a more ecological variant than radiators because of the way the space is heated. Instead of heating the room from top to bottom (as radiators do), underfloor heating ensures that the lower part of the room receives heat first.
Modern system solutions allow you to install heating on any type of floor, wall and ceiling.
We have heating systems:
-
Underfloor heating System Suchy
Li>
-
Underfloor heating System Wet
Li>
-
Underfloor heating Joist system
Li>
-
Underfloor heating Renovation System
Li>
Ul>
ALMAR SYSTEM STANDARD ALU I
Innovative and easy to install in the installation Standard Alu System Is the most widely used among dry floor heating systems without concrete screed for DIY. You can do it yourselfit is fast and simple. The advantage is its low weight and height, together with the UP underlay plate, weighs about 4.5 kg, which is very low compared to traditional (wet) systems, where weight is approximately 140 kg / m2
The system consists of polystyrene board EPS 200 covered metallized foil 0.4 mm thick , which the task is to better heat distribution over the entire surface.
The system is a very good solution for those who care about not loading the floors . Almar System Standard Alu is the best and cheapest of the available dry-built systems and convenient thanks to the use of polystyrene with alu metallized foil.
SYSTEM ADVANTAGES
-Low building height
-the lightest of systems
-Easy, quick installation
-good thermal insulation properties
– energy saving
-when the assembly is finished, the system is immediately ready for use
-total weight with UP 4,5kg underpile
– ALMAR SYSTEM STANDARD ALU board thickness with UP (HDF) underlay = 3mm
25mm + UP 3mm = 28mm
30mm + UP 3mm = 33mm
50mm + UP 3mm = 53 mm
TECHNICAL DATA
Declared heat transfer coefficient -U [W / Mk]
0.033 EPS 200 material 30 [kg / m3]
Declared thermal resistance R (m2K / W)
0.75 -25mm
0.87 -30mm
1.44-50mm
Permissible load gk [KNm2] 2.0
Fire classification – according to PNEN 13501-1: E
INSTALLATION DIAGRAM
– initial substrate
– ALMAR SYSTEM STANDARD ALU board (EPS 200 board covered with Alu metallized foil, 0.4mm thick)
– multilayer pipe
– UP underlay or screed (drywall)
– end floor (panel covering, parquet, tiles)
– edge tape
ALMAR SYSTEM STANDARD ALU II
Innovative and easy to install Standard Alu System Is the most widely used of dry floor heating systems without concrete screed for DIY DIY You can do it yourself > it is quick and simple. The advantage of the system is the low weight and height complete with the UP underlay weighs about 4.5 kg, it is very little compared to traditional (wet) systems, where the weight is about 140 kg / m2. The system consists of a EPS 200 polystyrene board covered with aluminum foil 0.12mm thick which task is to better heat distribution over the entire surface.
The system is a very good solution for those who care about not loading floors . Almar System Standard Alu is the best and the cheapest of the available dry systems j, and convenient thanks to foamed polystyrene with aluminum foil. p>
SYSTEM ADVANTAGES
-Low building height
-the lightest of systems
-Easy, quick installation
-good thermal insulation properties
– energy saving
-when the assembly is finished, the system is immediately ready for use
-total weight with UP 4,5kg underpile
– ALMAR SYSTEM STANDARD ALU board thickness with UP (HDF) underlay = 3mm
25mm + UP 3mm = 28mm
30mm + UP 3mm = 33mm
50mm + UP 3mm = 53 mm
SYSTEM OPTIONS
System heating comes in two variants
TECHNICAL DATA
Declared heat transfer coefficient -U [W / Mk]
0.033 EPS 200 material 30 [kg / m3]
Declared thermal resistance R (m2K / W)
0.68 -25mm
0.82 -30mm
1.38-50mm
Permissible load gk [KNm2] 2.0
Fire classification – according to PNEN 13501-1: E
INSTALLATION DIAGRAM
– initial substrate
– ALMAR SYSTEM STANDARD ALU board (EPS 200 board covered with Alu foil, 0.12mm thick)
– multilayer pipe
– UP underlay or screed (drywall)
– end floor (panel covering, parquet, tiles)
– edge tape
ALMAR SYSTEM STANDARD
Innovative and easy to install System Standard. It is the most commonly used among dry floor heating systems without concrete screed for DIY DIY You can do it yourself it is quick and easy . The advantage of the system is the low weight and height complete with the UP underlay weighs about 5 kg, it is very low compared to wet systems where the weight is from 140 kg / m2. The system consists of a EPS 200 polystyrene board and aluminum transmission sheets , which task is to better heat distribution over the entire surface. It is a very good solution for those who care about not loading ceilings. Almar System Standard is the best and cheapest of the available dry drywall systems
SYSTEM ADVANTAGES
-Low building height
-the lightest of the systems
– easy, quick assembly
– good thermal insulation properties
-Energy saving
– after installation, the system is immediately ready for use
-total weight including UP underlay about 4.5kg
– ALMAR SYSTEM STANDARD ALU board thickness with UP (HDF) underlay = 3mm
25mm + UP 3mm = 28mm
30mm + UP 3mm = 33mm
50mm + UP 3mm = 53 mm
SYSTEM OPTIONS
System heating comes in two variants
TECHNICAL DATA
Declared heat transfer coefficient -U [W / Mk]
0.033 EPS 200 material 30 [kg / m3]
Declared thermal resistance R (m2K / W)
0.80 -25mm
0.90 -30mm
1.50-50mm
Permissible load gk [KNm2] 2.0
Fire classification – according to PNEN 13501-1: E
INSTALLATION DIAGRAM
– initial substrate
– Board ALMAR SYSTEM STANDARD
– aluminum transmission sheet
– multilayer pipe
– UP underlay or screed (drywall)
– end floor (panel covering, parquet, tiles)
– edge tape
ALMAR SYSTEM ACUSTIC
Innovative and easy to install Almar Acustic heating system floor, it can be used wherever it is important to mute attenuation of ceilings. The wood fiber board provides good sound and thermal insulation. The system consists of a wood fiber porous board and aluminum transmission sheets , whose task is better heat distribution over the entire surface. ALMAR SYSTEM AKUSTIK can be used in residential and public buildings
SYSTEM ADVANTAGES
-Low building height
-light construction
-Easy, quick installation
-good thermal insulation properties
– energy saving
-when the assembly is finished, the system is immediately ready for use
-total weight with UP undercoat 6-9 kg (24-36mm)
-board thickness ALMAR AKUSTIK SYSTEM with UP (HDF) underlay 3mm
24mm + UP 3mm = 27mm
30mm + UP 3mm = 33mm
36mm + UP 3mm = 39mm
SYSTEM OPTIONS
System heating comes in two variants
TECHNICAL DATA
Material – wood fiber porous board
Declared thermal resistance R (m2K / W) 0.480 -24mm
thermal transmittance coefficient of the panel U [W / m 2 * K]: 0.465- (24mm board)
Sound absorption coefficient (250-500 Hz / 1000-2000 Hz) 0.11 / 0.31
Weight of material without end plate for 1m2 -9.10 [kg] 24mm board
Permissible load gk [KNm2] 2.0
INSTALLATION DIAGRAM
– initial substrate
– Board ALMAR AKUSTIK SYSTEM
– multilayer pipe
– UP underlay or screed (drywall)
– end floor (panel covering, parquet, tiles)
– edge tape
ALMAR SYSTEM ACUSTIC/ALU
Modern and easy to install Almar Acustic Alu System for heating floor , it can be used wherever it is important to mute ceilings. Wood fiber board provides good sound and thermal insulation. The system consists of a wood fiber porous board covered with 0.12mm thick aluminum foil whose task is to better heat distribution over the entire surface. ALMAR SYSTEM AKUSTIK / ALU can be used in any building. A convenient solution thanks to the use of aluminum metallized film
SYSTEM ADVANTAGES
-Low building height
-light construction
-Easy, quick installation
-good thermal insulation properties
– energy saving
-when the assembly is finished, the system is immediately ready for use
-total weight with UP undercoat 6-9 kg (24-36mm)
-board thickness ALMAR AKUSTIK SYSTEM with UP (HDF) underlay = 3mm
24mm + UP 3mm = 27mm
30mm + UP 3mm = 33mm
36mm + UP 3mm = 39mm
SYSTEM OPTIONS
System heating comes in two variants
TECHNICAL DATA
Material – wood fiber porous board
Declared thermal resistance R (m2K / W) 0.480 -24mm
thermal transmittance coefficient of the panel U [W / m 2 * K]: 0.465- (24mm board)
Sound absorption coefficient (250-500 Hz / 1000-2000 Hz) 0.11 / 0.31
Weight of material without end plate for 1m2 -9.10 [kg] 24mm board
Permissible load gk [KNm2] 2.0
INSTALLATION DIAGRAM
– initial substrate
– Board ALMAR AKUSTIK SYSTEM
– multilayer pipe
– UP underlay or screed (drywall)
– end floor (panel covering, parquet, tiles)
– edge tape
ALMAR SYSTEM ECO
Is a new and often used floor heating system in skeletal building. The system consists of chipboard material (MFP) and aluminum transmission sheets whose task is to better heat distribution. ALMAR SYSTEM ECO is a good heat conductor and has very good strength parameters, therefore it can be used as a floor construction.
SYSTEM ADVANTAGES
-Low building height
-Easy, quick installation
-application in the construction of frame houses
-good thermal insulation properties
– energy saving
-when the assembly is finished, the system is immediately ready for use
-total weight including UP underlay about 14 kg
-board thickness ALMAR ECO SYSTEM with UP (HDF) underlay = 3mm
22mm + UP 3mm = 25mm
25mm + UP 3mm = 28mm
SYSTEM OPTIONS
System heating comes in two variants
TECHNICAL DATA
Material – MFP ecological board (chipboard)
Mass of material per 1m2 -22 / 25mm -15.50 -17.30 kg
Declared thermal resistance R (m2K / W)
22mm – 0.1708
25mm- 0.1989
Heat transfer coefficient U [W / m2 * K]
22mm-5.9102
25mm -5,2002
Permissible load gk [KNm2] 2.0
INSTALLATION DIAGRAM
– initial substrate
– Board ALMAR SYSTEM ECO
– multilayer pipe
– UP underlay or screed (drywall)
– end floor (panel covering, parquet, tiles)
– edge tape
ALMAR SYSTEM GYPSUM
This is a very good system during renovation, renovation of buildings, low weight and the lowest building height is only 18 mm compared to traditional wet heating systems where the screed loads the ceiling and raises the floor height. Almar Gypsum System consists of gypso-nonwoven sheets . As the only heating system in which there is no need to use aluminum transmission sheets distributing heat over the entire surface because the gypso-nonwoven system plate is a good heat conductor. It is most often used on small surfaces of surface heating covered with ceramics, stone.
SYSTEM ADVANTAGES
-Minimum installation height -21mm
-best for renovation
-Easy, quick installation
-saving energy
-when the installation is completed, the system is immediately ready for use
– total weight with UP underlay board about 23 kg m2
-board thickness ALMAR span> 18 mm GYPSUM SYSTEM and 21 mm UP baseplate
SYSTEM OPTIONS
System heating comes in two variants
TECHNICAL DATA
Material -gypso-non-woven
Declared thermal resistance R (m2K / W) 18mm- 0.059
Heat transfer coefficient U [W / m2 * K] 18mm-17.7291
Permissible load gk [KNm2] 2.0
INSTALLATION DIAGRAM
– initial substrate
– Board ALMAR GYPSUM SYSTEM
– multilayer pipe
– UP backing board or fiberglass mesh embedded in adhesive
– end floor (panel covering, tiles, parquet)
– edge tape
LEGAR SYSTEM
Joist system option one:
Almar Standard Alu EPS 200 System Board coated with 0.4 mm aluminum foil for direct mounting on OSB, MFP, chipboard screwed to joists p>
Joist system, option two:
EPS 200 System Board with aluminum sheets placed in the grooves of the board, then the foamed panel is mounted on angle brackets
Which are fixed on the joists so that the top of the board system was flush with joists. Directly on joist beams, we arrange the floor from OSB, MFP, chipboard
SYSTEM ADVANTAGES
-Low building height
-light construction
-Easy, quick installation
-good thermal insulation properties
– energy saving
-when the assembly is finished, the system is immediately ready for use
-total weight with UP undercoat 6-9 kg (24-36mm)
-board thickness ALMAR AKUSTIK SYSTEM with UP (HDF) underlay = 3mm
24mm + UP 3mm = 27mm
30mm + UP 3mm = 33mm
36mm + UP 3mm = 39mm
SYSTEM OPTIONS
System heating comes in two variants
TECHNICAL DATA
Material -EPS 200 + aluminum sheet
Declared thermal resistance R (m2K / W) 1.48
INSTALLATION DIAGRAM
-legary p>
-mineral wool
-kątownik p>
-Board ALMAR SYSTEM STANDARD
-aluminium sheet
– multilayer pipe
-pillet board
– end floor (wooden floor, carpet, tiles)
– edge tape